Lead in drinking water: find the source, test your tap, then filter
Disclosure: We may earn a commission if you buy through links on this site, at no extra cost to you. It never changes what we recommend. How we make money.
You cannot see, taste or smell lead in water,[1] and on city water the problem usually starts in the pipes between the water main and your glass rather than at the treatment plant.[2] That is why the useful order is: find out what your service line and plumbing are made of, test the water at your own tap, then use a filter certified for lead if you need one.
How lead gets into tap water
EPA says lead enters drinking water when plumbing materials that contain lead corrode, especially where the water is acidic or low in minerals.[2] The most common sources are lead pipes, faucets and fixtures. In homes with a lead service line (the pipe connecting the home to the water main), that line is typically the most significant source.[2] Lead pipes are more likely in older cities and in homes built before 1986.[2]
Homes without a lead service line can still have lead. EPA says the most common problem in those homes is brass or chrome-plated brass faucets and plumbing joined with lead solder,[2] and CDC adds galvanized iron pipes to that list.[1] Penn State Extension notes brass fixtures can leach lead even in homes with plastic water lines.[3]
How much lead ends up in your glass depends on the water's acidity and minerals, how much lead it touches, its temperature, wear in the pipes, how long the water sits, and whether protective scale has formed inside the plumbing.[2][1] Penn State Extension says lead levels are usually highest in the first water out of the tap.[3]
Private well? Lead can come from your own plumbing too
Lead is not only a city-water issue. Penn State Extension says it is a potential concern for homes on private wells and springs as well, because the usual source is household plumbing, and that brass fittings on certain submersible well pumps used through the mid-1990s can corrode and release lead.[3] NSF says high lead in a private well may point to low pH: water below pH 7.0 is acidic and can leach lead from pipes and faucets.[4] Federal lead rules apply to public water systems, so Penn State notes they give little protection to private wells, springs and cisterns.[3] See How to test your well water for a well-testing plan.
Why it matters
EPA has set the maximum contaminant level goal for lead in drinking water at zero, because lead "can be harmful to human health even at low exposure levels."[2] EPA says young children, infants and fetuses are particularly vulnerable,[2] and CDC says no safe blood lead level has been identified for young children.[1] CDC notes that infants who drink formula made with lead-contaminated tap water may be at higher risk because of how much water they drink relative to their size.[1]
If you think you or your child has been exposed, CDC says to contact your child's healthcare provider; most people exposed to lead have no symptoms, and a blood lead test is the way to tell.[1] This page does not give medical advice.
Levels that matter
Lead does not have a regular maximum contaminant level. Because most lead comes from customers' plumbing, EPA regulates it with a treatment technique that requires water systems to control corrosion, and an "action level" that triggers extra steps.[2]
| Value | Level | What it means |
|---|---|---|
| Maximum contaminant level goal (MCLG) | Zero[2][5] | Non-enforceable health goal |
| Lead and Copper Rule action level (in force now) | 0.015 mg/L (15 µg/L, or ppb)[2][6] | If more than 10% of a water system's tap samples exceed it, the system must take further steps, educate the public and replace lead service line portions it controls[2] |
| Lead and Copper Rule Improvements (LCRI) action level | 0.010 mg/L (10 µg/L)[7][6] | Applies starting November 1, 2027[6] |
| NSF lead-reduction certification | Tested to reduce 150 ppb to 10 ppb or less (5 ppb under updated requirements, shown on the product's performance data sheet)[4] | What a certified filter has been verified to do |
Your lab may report µg/L (ppb) or mg/L (ppm): 15 µg/L is the same as 0.015 mg/L.[3] An action level is a trigger for your water system, not a "safe" line for your glass; EPA's health goal is zero.[2] Have numbers already? Enter them in our water test results checker.
The Lead and Copper Rule Improvements: status as of November 19, 2026
EPA finalized the LCRI in October 2024.[8] EPA says it requires water systems to identify and replace lead pipes within 10 years, tests drinking water more rigorously, and lowers the threshold that requires action.[9] Specifically, EPA says the rule:
- Lowers the lead action level from 15 µg/L to 10 µg/L.[8][7]
- Requires about 99% of systems to replace lead and certain galvanized service lines under their control in 10 years or less.[7]
- For sites with lead service lines, requires systems to collect and analyze both the first liter and the fifth liter and use the higher result.[8]
- Requires systems with multiple action level exceedances to make filters certified to reduce lead available to all consumers.[8]
EPA's compliance-dates fact sheet gives the LCRI compliance date as November 1, 2027; until then, systems follow the original Lead and Copper Rule plus a few 2021 requirements, including the service line inventory, notices about service line material, and 24-hour public notice of a lead action level exceedance at 0.015 mg/L.[6][7] An EPA primacy FAQ updated in June 2026 still refers to November 1, 2027 as the LCRI compliance date.[10] When we checked EPA's LCRI pages on November 19, 2026 (the main LCRI page was last updated December 29, 2025, and the LCRI Q&A March 11, 2026), they did not announce any reconsideration or change to these dates.[9][7] Rules can change, so check EPA's LCRI page for the current status. States may also set stricter rules than EPA.[2]
Find out if you have a lead service line
- Check your utility's inventory. Water systems must keep an inventory of service line materials, make it publicly accessible, and notify you if you are served by a lead line, a galvanized line that may be contaminated by lead, or a line of unknown material.[7]
- Call your water utility. NSF says the local water department can inspect the line, search records, or tell you whether lines in your area are known to contain lead.[4] If your utility has no information, EPA says a licensed plumber may be able to help.[2]
- Look at the pipe yourself. EPA's Protect Your Tap guide walks you through checking the pipe where it enters your home; all you need is a penny (or key) and a magnet.[11]
- If it is lead, ask about the utility's replacement program.[7][1] Watch for nearby construction: EPA says it can disturb a lead line and suddenly release more lead,[2] and CDC says your risk increases during replacement work and for up to six months afterward.[1]
EPA estimates about 4 million lead service lines serve properties across the United States.[12]
Test to confirm
Testing is the only sure way to know whether there is lead in your water, and every home's plumbing is different, so results differ from house to house.[2][11]
- Ask your utility first. CDC calls your local water authority your first source for testing, and many public water systems test residents' water on request.[1] EPA also suggests contacting your water utility to have your water tested.[2]
- Or use a certified lab. EPA recommends sending samples to a certified laboratory; your state or local drinking water program can provide a list.[11][13] Follow the lab's collection instructions and sample from the faucet you drink from.[11]
- Ask for a first-draw sample (and ideally a running sample). Penn State Extension describes a first-draw sample, collected first thing in the morning from cold water that sat in the pipes overnight, and a running sample taken after the cold water runs for at least one minute. Comparing the two helps locate the source.[3]
- Expect variation. CDC says results can vary with time of day, season, sampling method and water flow.[1] One clean result does not rule out lead.
On city water, also read your utility's annual Consumer Confidence Report; EPA requires community water systems to deliver one by July 1 each year.[2][14] Our guide How to read your water test results explains the units.
Reduce lead now, while you sort it out
These EPA and CDC steps cost little and can be used together.[2][1]
- Use only cold water for drinking, cooking and making baby formula. Hot tap water can contain more lead, and boiling does not remove it.[7][1]
- Run your water before drinking if it has been sitting. Showering, laundry or a dishwasher load also flushes the pipes. How long to run it depends on whether you have a lead service line and how long it is, so ask your utility for local flushing times.[2] Penn State cautions that flushing alone is not a reliable form of lead control.[3]
- Clean your faucet aerator regularly; lead particles can collect in the screen.[2]
- Consider certified bottled water for drinking; CDC says it can virtually eliminate exposure from water but may not be the most cost-effective long-term option.[1]
Match the treatment to your result
| Your situation | Likely source | Matching step |
|---|---|---|
| Detectable lead in a first-draw sample, or lead plumbing found | Service line, solder or fixtures in contact with standing water | Penn State says to take corrective action; a certified point-of-use filter for all drinking and cooking water is the most reliable way to prevent exposure[3] |
| Lead stays above 15 µg/L after running the cold water 1 to 2 minutes | Probably present before the water enters household plumbing: water supply, corroding well pump parts, or public water system lines[3] | Call your utility (city water) or have the pump checked (well); filter drinking water in the meantime[3][2] |
| You have a lead service line | Service line[2] | Join the utility's replacement program; CDC says people with lead service lines can reduce exposure with a filter for drinking and cooking water[7][1] |
| Private well with lead and pH below 7.0 | Acidic water corroding plumbing[4] | Acid-neutralizing treatment to raise pH, which prevents leaching rather than removing lead at the tap; retest afterward[4][3] |
Which filter certification? CDC says a point-of-use filter should be certified to NSF/ANSI 53 for lead removal and NSF/ANSI 42 for particulate removal.[1] Penn State says the package should state it meets NSF/ANSI 53 or 58 (reverse osmosis) for the reduction of lead.[3][15] EPA has a consumer tool for finding point-of-use and pitcher filters certified under NSF/ANSI 53 and 42 to reduce lead to 5 ppb or less.[16] NSF lists certified pitchers, faucet filters, under-sink systems, reverse osmosis units and refrigerator filters for lead, and notes there are currently no whole-house systems certified to reduce lead.[4]
Use it correctly: replace the cartridge on schedule, because an expired cartridge is less effective, and do not run hot water through the filter.[2]
- Point-of-use filter for lead (pitcher, faucet-mount or under-sink)Best fit: Lead in drinking and cooking water from a service line, solder or fixtures; cold water only; replace cartridges on schedule [1]Look for: NSF/ANSI 53 for lead reduction plus NSF/ANSI 42 for particulates
- Point-of-use reverse osmosis (kitchen tap)Best fit: Lead in drinking and cooking water at one tap, especially if you also need to reduce other contaminants [3]Look for: NSF/ANSI 58 with lead reduction listed
- Acid-neutralizing filter (private wells)Best fit: Well water with pH below 7.0 that is corroding lead from plumbing; prevents leaching rather than removing lead at the tap [3]Look for: Check the manufacturer's performance data; retest lead and pH after install
When to call a pro (or your utility)
- Any lead result on city water, or a running sample still high: call your water utility, and EPA also recommends contacting your local health department.[2][3]
- You are unsure what your service line is made of and the utility has no record: a licensed plumber may be able to help.[2]
- A private well with high lead: have the pump checked and test pH; Penn State notes acid-neutralizing filters may noticeably increase the water's hardness.[3]
- Someone in the home is pregnant, an infant or a young child and you suspect exposure: contact a healthcare provider about a blood lead test.[1]
What NOT to buy
- A kettle or boiling routine. Boiling does not remove lead.[2][1]
- A water softener as a lead fix. Penn State says softeners are not recommended for lead removal, usually sit upstream of the plumbing where lead comes from, and softened water is usually more corrosive.[3]
- A "whole-house lead filter". NSF says there are currently no whole-house systems certified to reduce lead.[4]
- A filter without a lead certification. Look for NSF/ANSI 53 (or 58 for reverse osmosis) with lead listed; certification to one standard does not cover every contaminant.[3][15]
- New faucets or fittings without a drinking-water certification. NSF suggests checking for NSF/ANSI/CAN 61 certification for drinking water contact.[4]
Frequently asked questions
Does boiling water remove lead?
No. EPA and CDC both say boiling does not remove lead from water. Use cold water for drinking, cooking and making baby formula.
Is it safe to shower or bathe in water that contains lead?
EPA and CDC say bathing and showering should be safe for adults and children, even if the water contains lead over EPA's action level, because human skin does not absorb lead in water.
Will a whole-house filter or water softener remove lead?
NSF notes that there are currently no whole-house systems certified to reduce lead, and Penn State Extension says water softeners are not recommended for lead removal. Use a point-of-use filter certified for lead at the tap you drink from.
My city water meets the rules. Can my tap still have lead?
Yes. EPA says lead usually comes from lead service lines and from brass or chrome-plated brass faucets and plumbing with lead solder inside or near the home, and Penn State Extension notes individual homes can have high lead even when most of the community does not. Testing at your own tap is the only way to know.
Sources
- About Lead in Drinking Water — U.S. CDC (accessed November 19, 2026)
- Basic Information about Lead in Drinking Water — U.S. EPA (accessed November 19, 2026)
- Lead in Drinking Water — Penn State Extension (accessed November 19, 2026)
- Lead in Drinking Water — NSF (accessed November 19, 2026)
- Lead and Copper Rule — U.S. EPA (accessed November 19, 2026)
- Fact Sheet: 2021 LCRR Requirements Retained in the Final Lead and Copper Rule Improvements and Compliance Dates — U.S. EPA (accessed November 19, 2026)
- LCRI Questions and Answers — U.S. EPA (accessed November 19, 2026)
- Fact Sheet: EPA's Lead and Copper Rule Improvements (October 2024) — U.S. EPA (accessed November 19, 2026)
- Lead and Copper Rule Improvements — U.S. EPA (accessed November 19, 2026)
- Lead & Copper Rule Primacy Extension Waiver Frequently Asked Questions (June 2026) — U.S. EPA (accessed November 19, 2026)
- Protect Your Tap: A Quick Check for Lead — U.S. EPA (accessed November 19, 2026)
- Lead Service Lines — U.S. EPA (accessed November 19, 2026)
- Contact Information for Certification Programs and Certified Laboratories for Drinking Water — U.S. EPA (accessed November 19, 2026)
- Consumer Confidence Reports (CCR) — U.S. EPA (accessed November 19, 2026)
- NSF Standards for Water Treatment Systems — NSF (accessed November 19, 2026)
- Consumer Tool for Identifying Point-of-Use and Pitcher Filters Certified to Reduce Lead — U.S. EPA (accessed November 19, 2026)